2011 Season Champs

[AScoda]

Extra Smedium for me!

Or large, whatever.

[shakedown067]

Anything someone would like to see on an autocross champion shirt? So far I can't stand what I've designed. I might have to go old school and breakout the pencil and paper.

[Native]

an evolution of last year's design?

(Eric - working on the list of shirt sizes - got about half of them...feel free to post these guys a deadline for if they want a shirt that fits. And you might want to fudge a bit to be sure there's plenty of time.)

[snookwheel]

Anything someone would like to see on an autocross champion shirt? So far I can't stand what I've designed. I might have to go old school and breakout the pencil and paper.

Post away! I'd like to see some of your art

[Loren]

For autox shirts, always like designs that show an active caricature of a car. Something sporty with fat tires, lots of camber, at full-tilt with an inside front or rear (as appropriate) tire in the air, etc.

[yamaha731]

I think every shirt should have a picture of my white mustang on it

[garage west]

I think every shirt should have a picture of my somewhat white mustang on it

Fixed.

[Dave]

as long as you keep the big design on the back, and if one on the front, just a small one over the left breast. never was a fan of the giant, gaudy design all over the front as well

[snookwheel]

For autox shirts, always like designs that show an active caricature of a car. Something sporty with fat tires, lots of camber, at full-tilt with an inside front or rear (as appropriate) tire in the air, etc.

Great idea! Fits the requirements!

[Native]

Anything someone would like to see on an autocross champion shirt? So far I can't stand what I've designed. I might have to go old school and breakout the pencil and paper.

I bet now you're sorry you asked.

[Tim_M]

Shirt design: I second the smaller front design. The larger rear design is well done, but I've noticed the 'plastic' backing makes the shirt a bit warmer than a smaller sized design. (minor point-I like the design)

As far as the car option, maybe put each winner's car on their shirt?

Or as yamaha said with a tweak...most people can relate to the traditional amercian sports car..red Corvette for everyone.



Seriously, congrats to all the winners and participants the same. Great time.

[shakedown067]

I bet now you're sorry you asked.

Not at all! Gives me design fuel...now I just have to get back to the drawing board. Thanks for all the suggestions fellas.

[Loren]

Another of my favorites was a very simple design that was used annually for the classic "MirrorKhana" event for about 30 years. Just a monochrome outline of two very recognizable cars facing off (as cars do in that event) at the starting line. The two cars in this case were a Spitfire (the event organizer drove one) and an MG Midget. Very appropriate for its time. Now, perhaps something like a Miata and a Civic would be more appropriate?

Of course, going back to my original suggestion... you could combine that with an angle similar to your avatar and end up with a pretty generic "car" that really sends a powerful message. That would be cool.

[shakedown067]

Yeah, I'm going to attempt a generic car, but based off a miata most likely. Something some what similar to what Scott posted, but with a couple of cones and a front wheel lifting. Haven't really drawn in a while, so this should be a fantastic project. Then I'll just colorize it via the computer. Hope to get it rolling and done by the end of the upcoming weekend.

[Solar]

I'm sure that what ever you have for a final design will be great, but will be debated and analyzed to death. But I will guarantee I will love it as long as the car is a 240SX !

[yamaha731]

A miata with the front wheel lifting good luck fineding that

[Jeremy]

[Solar]

Thats just wrong

[Loren]

A miata with the front wheel lifting good luck fineding that

[Native]

Ok - update time.

I still need shirt sizes from these guys, in no particular order:

Jamie Sculerati
Loren Williams
Brian Kollar
Lance Tavana
Mike Dassatti

If any of you know these folks, rattle their cages a bit, please.
I'm sure there's a deadline coming up (Eric?)...

As for the Annual "Membership" meeting and awards party, of those who have expressed preferences, it's looking like this:

Satuday the 27th - 3 votes
Sunday the 28th - 4 votes
either - 10 votes

We're not too far away from finally nailing down where and what we're doing, so if the date matters, make sure you lemme know.